Mason Sand for Patios in Fairbanks, IN

If you are laying a patio, setting pavers or pouring flatwork, the bedding under it decides how the job holds up. Indiana Rock Supply sells gravel and aggregate delivery in Fairbanks, IN, and we start most patio builds with #53 stone for the base. This is flat, silty valley ground, so a thin base moves fast.

Order online by the ton or the yard, and we run it to the site. Below is what we stock for patios, drives and drainage around Sullivan County.

Materials for Fairbanks Projects

Patio work is a bedding job before it is a paver job. You need a compacted base that will not pump when the silt underneath stays wet, then a thin leveling layer that lets the pavers sit flat. Get those two layers right and the surface stays put.

Start with #53 stone, the dense graded base most Indiana crews call for. It has fines that pack hard under a plate compactor and it carries the load, so it goes down first at depth. Over that, stone screenings give you the fine, workable bed for paver and flagstone setting and for leveling under a walkway.

Where the patio ties into a wall or a step, mason sand handles brick and block work and the joints between pavers. Under a slab or a poured pad, washed sand beds and levels the base. For a path off the patio, walkway gravel gives a finer, walkable surface that stays tight underfoot.

Ground and Conditions in Fairbanks

This part of Sullivan County sits on broad flat river valley and old lake-bed ground, silt and clay over low hills, with the thickest wind-blown silt in Indiana across these counties. That silt is the problem under a patio. Strip the cover and it washes quickly, and when it stays wet it will not carry a load.

A base that is too thin shows it the same way every time. The pavers rock at the corners, joints open up, and the whole patio settles unevenly after a wet spring. The fix is depth and compaction: excavate down past the soft silt, bring in #53 stone, and compact it in lifts before the bedding layer goes on.

Drainage matters here too. Valley bottoms and lake-bed flats drain slowly, and many upland soils hold water near the surface in wet seasons. If your patio sits low, plan a drainage layer and a fall away from the house. A run of drain rock at the edge or a French drain off the downspouts keeps water from sitting under the base.

Timing is worth planning around. Winter and spring are the high-water months on the river bottoms, so low sites build best from late spring through fall once the water drops and the silt dries. Winters here are milder than up north, but repeated freeze-thaw still heaves gravel and softens wet subgrades. Set footing depth to whatever the county or city building department requires rather than a northern figure.

Delivery to Fairbanks and the Surrounding Area

Order online and pick your quantity by the ton or by the cubic yard. Tons are the easier choice for stone and sand, since weight is what the truck scales read. Yards work better when you are thinking in volume, like filling a raised bed or backfilling a trench.

To estimate, measure the length and width of the area, then decide how deep the material goes. Multiply those three numbers together to get cubic feet, then convert to cubic yards or tons. If the math is not your thing, use the calculator on the product page and let it do the work.

We deliver bulk loads to Fairbanks and across Sullivan County, including Sullivan, Shelburn, Farmersburg, Dugger and Carlisle. Have the drop spot clear and reachable so the driver can place the pile where you want to shovel from.

What gravel is best for a driveway in Fairbanks?

For a new drive, start with #53 stone. It is the dense graded Indiana base that compacts hard and carries traffic, and it is what most crews here specify. Top it with #73 stone or driveway gravel for a tighter surface. On wet, silty ground, build the base deeper so the stone stays above the soft layer.

How much material will my project need?

Measure the length and width of the area, then set the depth you want. Multiply all three for cubic feet, then convert to cubic yards or tons. A base layer runs deeper than a bedding or topping layer, so figure each one separately. The calculator on each product page will convert your numbers for you.

Order Your Patio Materials in Fairbanks

Figure your square footage, set your base depth, and let the calculator turn it into tons or yards. Then place the order online and we will run the load out to your site in Fairbanks. Get your #53 stone, screenings and sand on one order and start setting pavers.